China mold and die industry in general is required to September

Note: in the past twenty years, China mold and die industry development, mould industry structure adjustment and reform, the pace of competitive mould manufacturing enterprise. But the overall level of die and mould industry is still behind the international advanced level for many years, still cannot meet die mold output, the domestic market demand of market of mold can meet 80% rate. Especially mould with high technical content, the middle-grade mould of less than 60 contented rate, in order to meet the needs of China's domestic market, every year to import a lot of mould, import and export trade deficit with China mold to 10 million dollars. Shenzhen mould technology to robben out hundreds of expert commissioner of China mold and die industry, Fraser should intensify their efforts in nine aspects.
1 increase production and development of high-grade mould.

At present, the world about 680 billion dollar value mould in 2005, China mold sales have reached 61 billion yuan (RMB), Japan, the United States ranked third in the world. For nearly a decade, the average annual output value increasing homebred mould 15.5% over the years, GPD growth rate, however, are still in short supply, homebred mould amount of mould with insufficient rate since, cheap, 80%, and high-grade die mold glut imports nearly 50%, especially large, precision, complex, long life. Mould gap China's import country, imported in mold amount equivalent to the value of homebred mould 25-30%. Because of the rapid development of China mold and die industry, boosting domestic consumption of steel, since the 21st century, domestic steel output increases rapidly.

2. Adjust enterprise organization structure, product structure, technology import and export structure and structure.

Mould manufacturing technology, the important base in our country, the mould manufacturing equipment manufacturing. Belongs Although China is already started manufacturing mold and die industry, but not form. Until the late 1980s, China mold and die industry to develop into the speedway. In recent years, not only the state-owned mould enterprise has been developing rapidly, three-capital enterprise, town (individual) mould enterprise development is also quite quickly. Although China mold and die industry is developing rapidly, but compared with demand, apparently, its main gap is focused on precision, large, complex, long life and mold domain. Because in the mould manufacturing, precision, life cycle and production capacity, etc, China and international average and developed countries still have a large gap, therefore, need to import a lot of mould.

In recent years, the mold industry structure adjustment and reform, which is mainly manifested in the increasing pace, large, complex, precision, long life, the middle-grade mould and standard mould development faster than general mold, Plastic mold and die ratio increases, Specialized factory producing ability increases; the number of its "Foreign" and the rapid development of private enterprises, Accelerate the share-holding system etc. From the regional distribution in pearl river delta, Yangtze river delta and the southeast coastal region of center for developing fast in the Midwest, south of quick development in the north. Currently, the development of the mould manufacturing and guangdong provinces are concentrated in zhejiang, anhui and jiangsu, Shanghai, shandong, etc in recent years has greatly developed. China mold and die industry in addition to continue improving production capacity, more will focus on internal structure adjustment and raise the level of technological development. Structure adjustment, mainly is to adjust, the product structure of specialization high-grade mold structure to develop, to import and export structure improvement, the middle-grade die forming analysis and improved structure, mould and multifunctional compound machining and laser technology in mould design, manufacturing, application of high speed cutting, polishing technology, informationization precision and direction.

3 die products.

At present domestic mold production cycle is higher than international level, but the product levels are relatively low, mainly in the mold cavity surface roughness, precision, life and structure, etc.

4 promotion development ability and economic benefits.

Our mould enterprise technical personnel ratio, low level is low, and pay no attention to product development, the market always in a passive position. Our every worker average mould in creating value of $1 million dollars, and mould industry developed countries abroad mostly 15 ~ 20 million dollars, some $25 to $30 million, and the relative is quite part of mould enterprise still follow past mill, truly realize management enterprise of modern enterprise management.

5) intensify the state of die and mould industry policy support.

Although the state has promulgated the mold industry industry policy, but the corresponding policy executive power, weak. Currently enjoy VAT of the mold enterprise, most companies only 185 still heavy taxes. Mould enterprise technical renovation imported equipment to pay taxes, the influence of quite a number of private enterprises, and technological progress loan very difficult.

6 increase personnel training, scientific research and development.

Mold industry's technology, capital, labor intensive industry, with the progress of The Times and the technical development, grasp and skillful use new technology talent shortage of abnormal, senior die locksmith and enterprise management personnel also very nervous. Due to poor mold enterprise benefit and research development and technical research, scientific research units and colleges of staring at the revenue, causing mold industry in the scientific research and development and technology input, cause mould technology development too little, slowly pace.

7. To improve technology level and equipment utilization. Sex

In recent years, China has been rapid progress, machine tool industry can offer complete precision processing equipment, but compared with foreign equipment, still have a large gap. Although many domestic enterprises has imported advanced equipment, but many of the overall level than many foreign enterprises equipped with much lower. Due to the system and capital and other reasons, the introduction of equipment, equipment and accessories not complete supporting phenomena are very common, the problem of low efficiency equipment is not properly solve long-term.

8. To strengthen cooperation, further improve the degree of specialization, standardization and commercialization.

Due to the long by "perfect" all-round "effect, low level of specialization of mould, specialization, the low degree of commercialization not careful. Current domestic production of goods each year, mould only 40 ﹪ mold, the rest for its. Mould enterprise, difficult to complete cooperation between large-scale sets of mould. Mould standardization and low level standard mould using coverage of mould quality, low cost and has greater influence, especially for mould manufacturing cycle has very big effect.

9 to die material and mould technology research.

Mould material performance, quality and variety problems tend to affect the quality of the die, life and cost, domestic and imported steel alloy compared with a large gap. Plastic, plank, equipment performance, but also directly influence to raise the level of mould.

Epilogue:

China mold manufacture as an industry started early, but the time is over 20 years of rapid development, is now a certain scale, and have produced some competitive mould manufacturing enterprise, the whole Chinese die &mould towards these great effort, will remain as, mould industry is still the sunny sky.